2024年3月27日发(作者：)

DULUX PEARLGLO WATER-BASED

TECHNICAL DATA SHEET

Version 5 – 2021 JUNE

THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS

PRODUCT DESCRIPTION

Superior, tough water-based non-drip mid-sheen enamel for interior and exterior use.

PRODUCT USES

· Suitable for direct application tofully cured and primed or previously painted plaster,

fibre cement or concrete surfaces.

· Also suitable for application to metal and wooden surfaces provided they have been

suitably primed.

· Recommended for all walls and ceilings especially where a superior low dirt pick-up

finish is required.

· Ideal for cupboards, doors, frames, skirting, and furniture.

FEATURES AND BENEFITS

·

·

·

·

·

·

·

·

Tough water-based satin enamel.

Steam and Grease Resistant

Superior stain resistance to household stains

Knock, chip and water resistant.

Fast drying and low odour – rapid room re-entry.

Non-Yellowing.

Superior exterior durability and UV resistant.

Direct application to sound, correctly prepared previously painted enamel surfaces.

PRODUCT INFORMATION

Appearance

Colour

Mid-sheen

White, Black and colours from the Dulux Colour System in

the Pastel Base 7, Medium Base 8, Deep Base 9 and Ultra

Deep Base 6.

Pure Acrylic

Approx. 1.25

By weight: Approx. 47%

By volume: Approx. 36%

Viscosity at 23°C: Approx. 100 KU

Approx. 8m² -10m² per litre depending on surface porosity,

profile and application method.

Binder Type

Density at 23°C

Solids Content

Packaged Viscosity

Spreading Rate

Recommended DFT per coat Min. 35µm. Max. 45µm.

Recommended WFT per coat Min. 100µm. Max. 125µm

Flash PointNon-flammable.

DULUX PEARLGLO WATER-BASED

APPLICATION INFORMATION

MixingStir until homogeneous with a flat paddle.

Application Surface conditions Surface Temperature between 10 - 35°C. Relative Humidity

between 10 - 85 % OR 2ºC above dew point minimum.

Application methods

Thinner

Drying Time

Recoating Time

Cleaning of equipment

Substrates

Brush, roller or airless spray.

Thinning not recommended. Ready for use after thorough

stirring.

Touch dry 60 minutes at 23ºC.

4 hours at 23ºC (Drying times will be extended during cold,

wet or humid conditions.)

After use, remove as much product as possible, and then

clean immediately with water.

Suitable for cement plaster, gypsum plaster, concrete, fibre

cement, various composite boards, metal and wooden

surfaces provided that appropriate preparation and priming

is carried out.

Do not apply during cold (below 10°C) or wet weather.

Do not apply directly to substrate without priming.

Not suitable for direct application to powdery or friable

surfaces whether previously painted or not.

Do not clean the surface within 7 days of applying.

Apply two to three finishing coats to new surfaces to achieve

a closed film and solid colour.

Precautions

Coats Required

SURFACE PREPARATION

Plaster sand should comply with SABS 1090 requirements. Plaster mix must be applied at a

minimum thickness of 10mm, curing to a hard and sound finish, free of soft and friable

material. MPA strength must comply with SABS 0164-1 (10MPA=2, 6:1 and 5MPA=4:1).

Ensure that surfaces are sound and free from dust, rust, oil, grease, dirt, and debris.

Surfaces must be thoroughly dry - no more than 12% moisture content.

NEW SURFACES

Cement Plaster (non-friable), Fibre Cement and Composite Boarding

· It is recommended that fresh plaster should be allowed one week drying for every 5mm

thickness; and longer in cold or damp weather.

· Spot-prime metal strips and nail heads with appropriate metal primer.

· For best paint system performance prime with one full coatDulux Plaster Primeror

Dulux Trade Alkali Resistant Primer.

· Rough surfaces may be filled withDulux Pre-Paint Smoothover orDulux Trade

Fillercoat to create a smooth base of even porosity.

Page2 of7


更多推荐